How do you really feel with regards to Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. See to it you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will assist you mount a new tub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the arrangement of your previous supply of water pipelines.
Your devices and also material checklist must consist of the following:
Getting ready for the Setup
First of all, the sustaining structure provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be quite troublesome due to the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub must wait till the bath tub has actually been made use of at least once as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be linked to the tap ends first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface in between the bathroom and the tiling, bring about issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes and also cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed reading our section about Installing A Bathtub. Thanks a ton for spending some time to browse our blog. Liked our post? Please share it. Help other people check it out. Thanks a bunch for your time. Come back soon.
Book An Estimate Now